Калькулятор Плиточного Клея

Q: На сколько квадратных метров хватает мешка плиточного клея 25 кг?

В среднем мешка 25 кг хватает на 5–8 м² при шпателе 6 мм. При укладке крупного формата гребенкой 10–12 мм расход увеличивается, и мешка хватает на 3–4,5 м².

Q: Какой зуб шпателя нужен для плитки 60×60 или 60×120 см?

Для керамогранита крупного формата требуется зуб 10 или 12 мм с обязательным методом двойного нанесения клея на основание и на обратную сторону плитки.

Q: Какова итоговая толщина клея под плиткой?

При вдавливании и притирке плитки гребни сплющиваются примерно наполовину, образуя монолитный слой толщиной 3–5 мм.

Q: Увеличивает ли метод двойного нанесения расход клея?

Да, контактный грунтовочный слой на тыльной стороне плитки увеличивает общий расход смеси примерно на 15–20%.

Q: Сколько воды требуется на один мешок смеси?

Обычно от 5 до 6 литров чистой холодной воды на мешок 25 кг в строгом соответствии с инструкцией производителя.

Q: В чем разница между базовым и эластичным клеем?

Эластичные клеи классов C2/S1 содержат полимерные добавки, предотвращающие растрескивание плитки при температурных деформациях теплых полов.

Q: Можно ли клеить плитку на мембрану DITRA?

Да, тонкий слой клея наносится под мембрану для фиксации к стяжке, и второй слой поверх мембраны для укладки плитки.

Q: Через сколько времени после укладки можно затирать швы?

Стандартный клей требует 24 часа до затирки швов и хождения. Быстротвердеющие составы позволяют затирать швы уже через 3–4 часа.

Q: Можно ли замешивать неполный мешок?

Да, строго взвешивая сухую смесь и отмеряя воду мерной емкостью в точной пропорции.

Q: Какова максимальная толщина клеевого слоя?

Для стандартных клеев предел составляет 5 мм. Для больших перепадов пола необходимо использовать толстослойный клей.

Бесплатный Калькулятор Клея для Плитки

Инструкция: Как Пользоваться Калькулятором

Точный расчет за 6 простых шагов — Быстрый режим для простых комнат и Профи для сложных оснований.

1 Step 1

1. Замер площади укладки

Введите длину × ширину, укажите готовую площадь в м² или сложите несколько помещений.

Tip: Measure niches, tub aprons and steps separately.

Step details: 1–6 Steps

1

Step 01

1. Замер площади укладки

Введите длину × ширину, укажите готовую площадь в м² или сложите несколько помещений.

Step 1

2

Step 02

2. Выбор формата плитки

Выберите стандартный формат (мозаика, 30×30, 60×60, 60×120 см) или задайте свой размер.

Step 2

3

Step 03

3. Подбор размера гребенки

Используйте автоподбор размера зуба шпателя по нормативам или укажите свой инструмент.

Step 3

4

Step 04

4. Выбор клеевой смеси

Выберите эластичный плиточный клей (C2 S1) или конкретный бренд производителя.

Step 4

5

Step 05

5. Запас на подрезку и потери

Добавьте 10–15% запаса на резку плитки и активируйте метод двойного нанесения.

Step 5

6

Step 06

6. Итоговый расчет мешков и воды

Получите точное количество целых мешков клея с округлением вверх и литры воды.

Step 6

Quick Answer

Сколько Плиточного Клея Нужно на 1 м²?

A standard 25 kg / 50 lb bag of thinset covers between 35 and 95 sq ft (3.5 to 9 m²) depending heavily on the trowel notch size:

High Yield

Мелкая плитка / мозаика

7 – 9 м² на мешок 25 кг

шпатель с зубом 4–6 мм

Most Common

Стандартная плитка 30×30 см

5 – 6.5 м² на мешок 25 кг

квадратный зуб 8–10 мм

Heavy Bed

Крупный формат (60×60 см+)

3.5 – 4.5 м² на мешок 25 кг

зуб 12 мм + нанесение на плитку

Interactive Estimator

Room Size to Bag Estimator

Adjust Room Size: 150 sq ft

20 sq ft 150 sq ft 350 sq ft 600 sq ft

Bags Needed

4 Bags

мешков по 25 кг / 50 lb

Total Mortar Weight

200 lb

~91 kg

Mixing Water

5.5 gal

clean cold water

Estimated Cost

$99.96

@ ~$25 per bag

* Based on standard format with 10% waste allowance. Open Full Pro Calculator →

Key Factors Determining Real Mortar Usage:

Trowel Notch Depth

A 12 mm notch applies more than double the volume of a 4 mm notch.

Back-Buttering Requirement

Mandatory for tiles > 15 inches to achieve 80-95% coverage (+15-20% mortar).

Product Density

Lightweight polymer mortars cover identical surface area with less weight.

Substrate & Membranes

Uneven screeds and uncoupling membranes absorb extra mortar.

Technical Standards

Таблица Расхода Плиточного Клея

Official coverage benchmarks per 25 kg / 50 lb bag across trowel tooth geometries.

Cross-Section Profile CAD Profile

Width: 1/2" (12.7mm) • Depth: 1/2" (12.7mm)

Select Trowel Notch Type:

1/2" × 1/2" Square Notch

Essential for achieving ANSI 80% (dry) and 95% (wet) bond contact.

Coverage / Bag 35 – 45 sq ft

Usage Rate ~1.11 – 1.43 lb/sq ft

Ridge Volume Heavy Volume

Trowel Notch	Profile	Typical Application	Coverage / Bag	Usage (kg/m² or lb/sq ft)	Notes
4 mm / 3/16" V-Notch	V-Notch	Mosaics, glass tile, small wall tiles	8.5 – 10.5 m² (85-100 sq ft)	~2.4 – 2.8 kg/m²	Prevents squeeze-out between narrow joints.
6 mm / 1/4" Square	Square	Tiles up to 20×20 cm (8×8"), subway wall tiles	7.0 – 8.5 m² (75-90 sq ft)	~2.8 – 3.5 kg/m²	Standard notch for residential ceramic tile.
8-10 mm / 3/8" Square	Square	Floor tiles 30×30 cm (12×12"), pavers	5.0 – 6.5 m² (50-65 sq ft)	~3.8 – 5.0 kg/m²	Compensates slight substrate unevenness.
12 mm / 1/2" Square	Square	Large format 30×60, 60×60 cm (LFT)	3.5 – 4.5 m² (35-45 sq ft)	~5.5 – 7.0 kg/m²	Essential for 80% to 95% continuous contact.
15 mm / 3/4" U-Notch	U-Notch	XXL porcelain panels, natural stone	2.8 – 3.5 m² (28-35 sq ft)	~7.0 – 8.8 kg/m²	Eliminates hollow air pockets under heavy tiles.
Euro Slanted Notch	Slanted	Heated floors, outdoor terraces, slabs	3.0 – 4.0 m² (30-40 sq ft)	~6.0 – 8.0 kg/m²	Channels expel trapped air smoothly.

Tool Selection

Руководство по Выбору Зубчатого Шпателя

Match your tile dimensions to the recommended notch size and compressed bed thickness:

Tile Size	Tile Type	Notch Size	Profile	Compressed Bed	Usage Rate
Mosaics (1" - 2")	Glass / Ceramic	4 mm / 3/16"	V-Notch	~1.5 mm	Low consumption Prevents squeeze out into grout joints.
Subway & Wall (4×4)	Glazed ceramic	6 mm / 1/4"	Square	~2.0 mm	Moderate Provides non-sag vertical hold.
Floor 30×30 cm (12×12)	Porcelain / Ceramic	8 mm / 3/8"	Square	~3.0 mm	Standard Straight line troweling pattern.
Large Format 30×60 cm (12×24)	Rectified porcelain	12 mm / 1/2"	Square / U	~4.0 mm	High Back-buttering mandatory for 80%+ contact.
Large Square 60×60 cm (24×24)	Polished porcelain	12 mm / Euro	Euro / U	~4.5 mm	Very high Requires medium-bed non-slump mortar.
Wood Plank (20×120 cm)	Plank porcelain	12 mm / Euro	Slanted	~4.5 mm	Very high Install with max 33% offset to prevent lippage.
Uncoupling Membrane (DITRA)	Polyethylene mat	4 mm / 3/16"	V / Square	~1.5 mm under mat	Separate coat (~15 m²/bag) Follow membrane manufacturer specifications.

Format Guide

Расход Клея в Зависимости от Размера Плитки

Recommended trowel size, average coverage and installation criteria by format:

Mosaics & Sheets

Up to 5×5 cm

Thin bed prevents squeeze-out between small joints.

Зубчатый шпатель: 4 mm V-Notch

Расход / площадь: 8 – 10 m² / bag

Толщина слоя под плиткой: ~1.5 mm

Двойное нанесение: Not required

Класс клея: C2 TE S1 Polymer

Subway & Wall Tiles

7.5×15 to 10×30 cm

Non-sag thixotropic hold on vertical walls.

Зубчатый шпатель: 6 mm Square

Расход / площадь: 7 – 8.5 m² / bag

Толщина слоя под плиткой: ~2.0 mm

Двойное нанесение: Optional

Класс клея: C2 T Non-Sag

Standard 30×30 cm

30×30 cm (12×12")

Classic format with easy bed leveling.

Зубчатый шпатель: 8 mm Square

Расход / площадь: 5 – 6.5 m² / bag

Толщина слоя под плиткой: ~3.0 mm

Двойное нанесение: Recommended for uneven backs

Класс клея: C2 TE Standard

Large Format 30×60 cm

30×60 cm (12×24")

Back-buttering mandatory to eliminate hollow spots.

Зубчатый шпатель: 12 mm Square

Расход / площадь: 3.5 – 4.5 m² / bag

Толщина слоя под плиткой: ~4.0 mm

Двойное нанесение: Mandatory (Double Buttering)

Класс клея: C2 S1 Medium-Bed

Large Square 60×60 cm

60×60 cm (24×24")

Heavy tiles require high bond strength.

Зубчатый шпатель: 12 mm or Euro

Расход / площадь: 3 – 4 m² / bag

Толщина слоя под плиткой: ~4.5 mm

Двойное нанесение: Mandatory

Класс клея: C2 S1 Flexible

Wood-Look Planks

20×120 cm

Install with max 33% offset to prevent lippage.

Зубчатый шпатель: 12 mm Slanted

Расход / площадь: 3 – 3.8 m² / bag

Толщина слоя под плиткой: ~4.5 mm

Двойное нанесение: Mandatory

Класс клея: C2 S1 Non-Slump

Gauged Porcelain Panels

120×260 cm+

Requires 2-person handling with vacuum suction cups.

Зубчатый шпатель: Euro Slanted

Расход / площадь: 2.5 – 3.5 m² / bag

Толщина слоя под плиткой: ~4.0 mm

Двойное нанесение: Double coat floor + slab

Класс клея: C2 S2 Ultra-Flexible

Thickness & Bed Dynamics

Какова Толщина Клеевого Слоя Под Плиткой?

A common misconception is assuming trowel notch height equals final bed thickness under installed tile.

Interactive Cross-Section

Bond Coverage: Contact: 45% (Uncompressed)

Tile Body (10 mm / 3/8") 3/8" (9.5mm)

Combed Ridges (12 mm / 1/2")

/// SUBSTRATE CONCRETE BASE ///

Bed Thickness: Final Bed: ~3.5 mm (~1/8") Total Elevation: Total Elevation: ~13.5 mm

Physics Simulator

Tile Embedment & Ridge Collapse

Adjust Embedment Pressure:

Embedment Pressure: 0%

0% Fresh Combed 50% Squeezed 100% Full Collapse (95%)

Why Collapse Matters:

Uncompressed ridges leave 50% hollow air channels. Sliding tile collapses ridges into a continuous void-free structural bed.

1 Full Notch Height

Fresh Combed Ridges

Troweled at 45 degrees leaving open air channels.

Stage 01 TCNA A108

2 ~35-45% of Notch

Tile Pressed & Shifted

Ridges collapse sideways expelling air pockets.

Stage 02 TCNA A108

3 ~3.0 - 4.5 mm

Fully Cured Bed

Solid rock-like bond after cementitious hydration.

Stage 03 TCNA A108

Q Can I use thinset to level 15 mm of floor unevenness?

Limit Alert

No. Standard thinset shrinks if applied over 5 mm (1/4"). Use self-leveling underlayment or specialized medium-bed mortar.

Q How to calculate total floor elevation for doors?

Failure Risk

Tile thickness + compressed mortar bed + membrane = total elevation (typically 14 to 18 mm).

Visual Systems

Интерактивные Схемы и Дерево Решений ANSI

Explore 5-layer uncoupling membrane anatomy and select the right ANSI / EN standard for your project.

Schluter DITRA Cross-Section Click on any layer to inspect technical details:

5-Layer Membrane Installation Anatomy

Click any layer of the uncoupling assembly below to inspect manufacturer specifications and coverage rules:

Uncoupling Membrane (Stress Relief Layer) Per roll

Absorbs substrate shear movements.

Smart Tool

Mortar Specification Wizard

Decision Wizard

Select 3 parameters to determine the exact mortar classification:

1. Tile Type Step 1

2. Substrate Step 2

3. Moisture Exposure Step 3

Recommended Class: ANSI A118.4HT

Modified Large and Heavy Tile (LFT) Mortar

Porcelain large-format tile requires high-polymer modified mortar with non-sag HT performance.

Environment Guide

Требования к Различным Основаниям

Substrate porosity, flexibility and moisture movement guide prep and adhesive choice:

Rigidity Check L/360 Compliant

J1

J2

Deflection Rating: L/360 Status: Safe for Tile

TCNA Structural Deflection Standard

Subfloor Deflection Gauge

TCNA requires subfloors to deflect no more than L/360 for ceramic/porcelain and L/720 for natural stone under full live loads:

Joist Spacing:

Tile Type:

Standard Compliance: Standard 3/4" subfloor over 16" o.c. joists is compliant with ANSI A108.01. Direct tile bond acceptable with A118.11 mortar or CBU underlayment.

Standard / L/360

Concrete Slab / Screed

The most rigid and stable base for tile.

Preparation: Clean, dust-free; check residual moisture

Impact on Usage: Standard base (no extra consumption)

Cement Backer Board (CBU)

Standard waterproof backing for showers and bathrooms.

Preparation: Tape joints with alkali-resistant mesh and mortar

Impact on Usage: +5% (board absorbs moisture)

Plywood / Wood Subfloor

Wood moves with humidity; avoid direct bond without membrane.

Preparation: Securely screwed; uncoupling membrane recommended

Impact on Usage: Membrane layer recommended

Uncoupling Membrane (DITRA)

Isolates floor cracks so they never transfer to tile.

Preparation: Embed fleece solidly into fresh mortar

Impact on Usage: Double coat application (+100% total)

Recommended Product: Schluter ALL-SET / C2 TE

C2 S1 Renovation Grade

Tile-Over-Existing-Tile

Saves demolition dust and time during renovations.

Preparation: Degrease, scuff surface and apply bonding primer

Impact on Usage: Requires primer layer

Drywall / Gypsum Board

Suitable only for dry rooms without water spray.

Preparation: Dust-free and primed with acrylic sealer

Impact on Usage: Low consumption on smooth board

Факторы, Влияющие на Расход Клея

On real jobsites, physical conditions deviate from theoretical lab numbers:

01 +15% to -20%

Trowel Angle & Pressure

Troweling at 60 degrees forms full ridges, while a flat 45-degree angle reduces thickness.

Severity Level Moderate

02 +10% to +25%

Tile Back Waffle Pattern

Deep grooves on tile undersides consume mortar to fill hollows.

Severity Level High

03 +15% to +30%

Substrate Unevenness

An unlevel floor forces the setter to thicken the mortar bed.

Severity Level Critical

04 +15% to +20%

Mandatory Back-Buttering

Applying a flat contact skim to large tiles reduces coverage per bag.

Severity Level High

05 +10% loss

Temperature & Air Drafts

Summer heat skins over mortar in the bucket prematurely.

Severity Level Moderate

06 +5% loss

Residue on Bucket & Tools

Mortar adhering to mixing paddles and pail walls.

Severity Level Low

07 +10% to +15%

Diagonal Layout & Cuts

Creates extra perimeter cuts and adjustments.

Severity Level High

08 +30% to +40%

DITRA Membrane Cavities

Filling square dovetail pockets takes extra mortar volume.

Severity Level Critical

Standard Rule Compliant Pass

Target: 80% Simulated: 82%

TCNA A108 Specification Standard

80% vs 95% Mortar Contact Rule

Minimum bond contact requirements to prevent cracked or debonded tiles:

80% Contact Requirement (Dry Interior)

For dry interior floors, at least 80% of tile back must be supported with continuous mortar bed.

2-Step Mortar Calculation for Schluter DITRA

Installing uncoupling membranes requires calculating 2 separate mortar coats:

Layer 1: Under Mat (Substrate to Mat) Layer 1

4 mm / 3/16" V-notch trowel

Yield: ~15 – 18 m² per 25 kg bag

Layer 2: Over Mat (Mat to Tile) Layer 2

10-12 mm notch by tile size

Yield: ~3.5 – 4.5 m² per 25 kg bag

For 20 m² with DITRA, you need ~1.5 bags for the mat + 5 bags for tiles = 7 bags total.

Standards & Specifications

Стандарты ANSI и ГОСТ на Плиточный Клей

International performance classifications explained clearly:

C1 / A118.1 Budget

Tier 0: Unmodified

Standard Mortar

For porous ceramic tiles on rigid concrete.

Polymers: Standard

Flexibility: Rigid

Water Resist: Normal

Strength Rating: ★☆☆☆

C2 / A118.4 Standard

Tier 1: Modified

Polymer-Modified Thinset

Industry standard for porcelain and indoor floors.

Polymers: Modified

Flexibility: Medium

Water Resist: Good

Strength Rating: ★★☆☆

C2 S1 / A118.11 Mid-High

Tier 2: Wood-Bond

Deformable Flex Mortar

For large format tiles and heated screeds.

Polymers: High

Flexibility: Flex ≥ 2.5 mm

Water Resist: Very good

Strength Rating: ★★★☆

C2 S2 / A118.15 Premium

Tier 3: Super-Bond Elite

Highly Deformable Super-Bond

For pools, wood floors, facades and gigantic slabs.

Polymers: Maximum

Flexibility: Flex ≥ 5.0 mm

Water Resist: Excellent

Strength Rating: ★★★★

Interactive Metric Matrix

Mechanical Strength Comparison

Click any classification below to dynamically compare shear bond strength, flexural tolerance, and polymer concentration:

Shear Bond Strength 600+ psi (A118.15)

Flexibility (S1/S2) Very High

Polymer Content Maximum

Material	Chemical Base	Best Application	Wet / Exterior Safe	Price Tier
Standard Thinset	Portland Cement + Polymer	Universal floor and wall	Yes / Excellent	$$ (Standard)
Medium-Bed Mortar	Coarse aggregate cement	Tiles > 15" & leveling	Yes / Recommended	$$$ (Medium)
Super-Bond (S2)	Elastomeric polymer	Pools, terraces, wood	Yes / Maximum	$$$$ (Premium)
Tile Mastic (D2)	Water-based acrylic paste	Kitchen backsplashes only	No (dissolves in water)	$$ (Ready mix)
Epoxy Mortar (R2)	2-Part epoxy resin	Commercial kitchens, spas	Yes / Impermeable	$$$$$ (Highest)

Mixing Best Practice

Правильное Затворение Клея и Расчет Воды

Correct mixing ensures polymers develop maximum shear bond strength:

Phase 01

1. Add Water to Pail First

Always pour clean cold water into the bucket first, then add powder gradually to prevent dry clumps at the bottom.

Phase 02

2. Mix at Low Speed (3–5 min)

Use a drill under 500 RPM. High speed traps air bubbles that weaken tensile bond strength.

Phase 03

3. 10-Minute Slake Time (Mandatory Rest)

Let mortar rest undisturbed for 10 minutes so polymers activate chemically.

Phase 04

4. Remix for 1 Minute – Ready!

Remix for 1 minute without adding any extra water, even if it feels thicker.

Таймер созревания раствора (10 минут)

05:00 Digital Timer

Калькулятор воды для неполного мешка

Calculate exact water in liters or quarts for partial batches:

Accurate Water Ratio

Select Product:

Measurement Mode:

Amount to Mix:

Target Consistency: Target: Creamy Peanut Butter

Quarts:

2.75 qt

Gallons:

0.69 gal

Fluid Oz:

88 fl oz

Liters of Water:

2.60 L

Warning: Excess water ruins bond strength and causes hollow tiles.

Practical Calculations

Примеры Расчета для Разных Помещений

Real project scenarios with transparent math. Click 'Load this room' to try:

4 m² (40 sq ft)

Powder Room (30×30 Ceramic)

Formula Calculation:

4 m² + 10% waste = 4.4 m² ÷ 5 m²/bag = 0.88 bags

A single bag easily covers powder rooms.

Trowel: 8 mm Square

Yield Result: Buy: 1 Bag

5 m² (50 sq ft)

Kitchen Backsplash (Subway Tile)

Formula Calculation:

5 m² + 10% = 5.5 m² ÷ 8 m²/bag = 0.69 bags

Non-sag wall mortar.

Trowel: 6 mm Square

Yield Result: Buy: 1 Bag

10 m² (100 sq ft)

Master Bath (30×60 LFT)

Formula Calculation:

10 m² + 10% + 15% back-butter = 12.65 m² ÷ 4 = 3.16 bags

Back-buttering requires 4th bag.

Trowel: 12 mm Square

Yield Result: Buy: 4 Bags

15 m² (150 sq ft)

Walk-in Shower (Floor & Walls)

Formula Calculation:

15 m² effective ÷ ~4 m²/bag = 3.75 bags

High-flex waterproof mortar required.

Trowel: Floor: 6 mm / Wall: 10 mm

Yield Result: Buy: 4 Bags

30 m² (300 sq ft)

Open Kitchen with DITRA

Formula Calculation:

Under mat: 2 bags + on mat: 8 bags = 10 bags

Double layer application for membrane.

Trowel: Under: 4 mm / Over: 12 mm

Yield Result: Buy: 10 Bags

50 m² (500 sq ft)

Basement Floor (60×60 Porcelain)

Formula Calculation:

50 m² + 12% waste + buttering = 65 m² ÷ 3.5 = 18.5 bags

Pallet delivery recommended for this quantity.

Trowel: 12 mm LFT

Yield Result: Buy: 19 Bags

80 m² (800 sq ft)

Whole House (Plank Porcelain)

Formula Calculation:

80 m² + 15% waste = 105 m² ÷ 3.3 = 31.8 bags

Long planks produce more offcut waste.

Trowel: Euro Slanted

Yield Result: Buy: 32 Bags

120 m² (1,200 sq ft)

Commercial Restaurant Floor

Formula Calculation:

120 m² + 10% = 152 m² ÷ 3.8 = 40 bags

C2 S1 heavy duty commercial bond.

Trowel: 12 mm Square

Yield Result: Buy: 40 Bags (1 Tonne)

Manufacturer Archive

База Данных Плиточных Клеев и Брендов

Verified coverage benchmarks and water ratios directly from official Technical Data Sheets (TDS):

Product & Manufacturer	Standard Class	Yield 6 mm (1/4")	Yield 12 mm (1/2")	Water Ratio	Data Sheet
Generic Polymer-Modified Thinset (ANSI A118.4) Generic / Standard Industry Average 50 lb bag	ANSI A118.4 / A118.11	82.5 sq ft	45 sq ft	5–6 qts	Техническая карта (TDS) ↗
MAPEI Ultraflex 2 Professional Tile Mortar MAPEI 50 lb bag	ANSI A118.4, ANSI A118.11	82.5 sq ft	41.5 sq ft	5–6 qts	Техническая карта (TDS) ↗
MAPEI Ultraflex LFT Large Format Mortar MAPEI 50 lb bag	ANSI A118.4HT, ANSI A118.11	70 sq ft	40 sq ft	5.5–6 qts	Техническая карта (TDS) ↗
Custom VersaBond Fortified Thin-Set Mortar Custom Building Products 50 lb bag	ANSI A118.4, ANSI A118.11	90 sq ft	44.5 sq ft	5.5–6 qts	Техническая карта (TDS) ↗
Custom VersaBond LFT Large Format Mortar Custom Building Products 50 lb bag	ANSI A118.4HT, ANSI A118.11	75 sq ft	38.5 sq ft	5.5–6 qts	Техническая карта (TDS) ↗
LATICRETE 254 Platinum Multipurpose Thin-Set LATICRETE 50 lb bag	ANSI A118.15, ANSI A118.4, ANSI A118.11	87.5 sq ft	43.5 sq ft	5.25–5.75 qts	Техническая карта (TDS) ↗
LATICRETE 253 Gold Modified Thin-Set LATICRETE 50 lb bag	ANSI A118.4, ANSI A118.11	85 sq ft	41.5 sq ft	5–5.5 qts	Техническая карта (TDS) ↗
Schluter ALL-SET Specialized Tile Mortar Schluter Systems 50 lb bag	ANSI A118.4T, ANSI A118.11, ANSI A118.15T	80 sq ft	38.5 sq ft	4.75–5.25 qts	Техническая карта (TDS) ↗
ARDEX X 5 Flexible Tile and Stone Mortar ARDEX 40 lb bag	ANSI A118.4, ANSI A118.11	70 sq ft	34 sq ft	4.5–5 qts	Техническая карта (TDS) ↗
TEC Full Flex Premium Polymer-Modified Mortar TEC (H.B. Fuller) 50 lb bag	ANSI A118.4, ANSI A118.11	81.5 sq ft	40 sq ft	5–5.5 qts	Техническая карта (TDS) ↗